[IA64] add arch/ia64/kernel/Makefile to sparse tree

Signed-off-by: Alex Williamson <alex.williamson@hp.com>

diff --git a/linux-2.6-xen-sparse/arch/ia64/kernel/Makefile b/linux-2.6-xen-sparse/arch/ia64/kernel/Makefile
new file mode 100644 (file)
index 0000000..09a0dbc
--- /dev/null
+++ b/linux-2.6-xen-sparse/arch/ia64/kernel/Makefile
@@ -0,0 +1,61 @@
+#
+# Makefile for the linux kernel.
+#
+
+extra-y        := head.o init_task.o vmlinux.lds
+
+obj-y := acpi.o entry.o efi.o efi_stub.o gate-data.o fsys.o ia64_ksyms.o irq.o irq_ia64.o      \
+        irq_lsapic.o ivt.o machvec.o pal.o patch.o process.o perfmon.o ptrace.o sal.o          \
+        salinfo.o semaphore.o setup.o signal.o sys_ia64.o time.o traps.o unaligned.o \
+        unwind.o mca.o mca_asm.o topology.o
+
+obj-$(CONFIG_IA64_BRL_EMU)     += brl_emu.o
+obj-$(CONFIG_IA64_GENERIC)     += acpi-ext.o
+obj-$(CONFIG_IA64_HP_ZX1)      += acpi-ext.o
+obj-$(CONFIG_IA64_HP_ZX1_SWIOTLB) += acpi-ext.o
+
+ifneq ($(CONFIG_ACPI_PROCESSOR),)
+obj-y                          += acpi-processor.o
+endif
+
+obj-$(CONFIG_IA64_PALINFO)     += palinfo.o
+obj-$(CONFIG_IOSAPIC)          += iosapic.o
+obj-$(CONFIG_MODULES)          += module.o
+obj-$(CONFIG_SMP)              += smp.o smpboot.o
+obj-$(CONFIG_NUMA)             += numa.o
+obj-$(CONFIG_PERFMON)          += perfmon_default_smpl.o
+obj-$(CONFIG_IA64_CYCLONE)     += cyclone.o
+obj-$(CONFIG_CPU_FREQ)         += cpufreq/
+obj-$(CONFIG_IA64_MCA_RECOVERY)        += mca_recovery.o
+obj-$(CONFIG_KPROBES)          += kprobes.o jprobes.o
+obj-$(CONFIG_IA64_UNCACHED_ALLOCATOR)  += uncached.o
+mca_recovery-y                 += mca_drv.o mca_drv_asm.o
+
+# The gate DSO image is built using a special linker script.
+targets += gate.so gate-syms.o
+
+extra-y += gate.so gate-syms.o gate.lds gate.o
+
+# fp_emulate() expects f2-f5,f16-f31 to contain the user-level state.
+CFLAGS_traps.o  += -mfixed-range=f2-f5,f16-f31
+
+CPPFLAGS_gate.lds := -P -C -U$(ARCH)
+
+quiet_cmd_gate = GATE $@
+      cmd_gate = $(CC) -nostdlib $(GATECFLAGS_$(@F)) -Wl,-T,$(filter-out FORCE,$^) -o $@
+
+GATECFLAGS_gate.so = -shared -s -Wl,-soname=linux-gate.so.1
+$(obj)/gate.so: $(obj)/gate.lds $(obj)/gate.o FORCE
+       $(call if_changed,gate)
+
+$(obj)/built-in.o: $(obj)/gate-syms.o
+$(obj)/built-in.o: ld_flags += -R $(obj)/gate-syms.o
+
+GATECFLAGS_gate-syms.o = -r
+$(obj)/gate-syms.o: $(obj)/gate.lds $(obj)/gate.o FORCE
+       $(call if_changed,gate)
+
+# gate-data.o contains the gate DSO image as data in section .data.gate.
+# We must build gate.so before we can assemble it.
+# Note: kbuild does not track this dependency due to usage of .incbin
+$(obj)/gate-data.o: $(obj)/gate.so